Essential Plumber Tips for Bathtub Installation
Essential Plumber Tips for Bathtub Installation
Blog Article
We've stumbled upon this post about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the web and accepted it made sense to talk about it with you on this site.

Installing a bath tub isn't exactly brain surgery, yet it does require strong plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately difficult task. If the old tub is conveniently easily accessible, the job can relocate easily; if you have to open up a wall to get rid of the old tub and also place the new tub, the task is much harder. In either situation, the project is within a home handyman's abilities, although you will certainly need a helper to leave the old bathtub and also set in the brand-new one. Make certain you have qualified on your own for the job and also fit attempting it. Instead of hiring a contractor to take over a halfway-completed task, it is far better to take into consideration utilizing one before you start. Opportunities are you might need a professional plumber to make tube connections.
This write-up will certainly aid you mount a brand-new bathtub in your restroom if you have actually currently acquired a new tub and do not require to transform the arrangement of your previous water pipelines.
Your devices and product list need to comprise the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is disconnect the water supply. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of eliminating the existing faucets can be fairly problematic due to the limited access that is frequently the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly come from the pipelines. Once the supply pipes have been removed, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming during this process. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old securing compound.
Before going on to fit the new faucets, compare the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a connection to the current supply pipes.
If you need to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin guaranteeing that the washing machines are in area in between the faucet and the sink. Safeguard the faucet in position with the maker provided backnut. As soon as the faucet is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The previous type needs to be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Bathtub
Using both wooden boards under its feet, place the tub in the needed placement. The wood boards are handy in evenly spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub till the level reads degree.
To set up taps, fit the bottom of the furthest flexible tap port to the proper supply pipe by making a compression join; after that do the very same for the various other tap.
Turn on the water supply as well as inspect all joints and new pipework for leaks and tighten them if essential. Fill up the tub and also examine the overflow electrical outlet and the regular outlet for leaks.
Finally, fix the bath paneling as described in the supplier's instruction manual. Tiling and sealing around the tub needs to wait up until the bathtub has actually been made use of at least when as this will certainly settle it right into its final placement.
Planning for the Setup
Firstly, the sustaining framework supplied with the bathroom needs to be fitted (if needed) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets device to avoid pressure on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps making use of 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently prepare to be suited its last placement.
Tiling Around the Bath tub
In the location where the bathroom satisfies the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to break an inflexible seal, triggering the water to pass through the wall between the bathroom and also the tiling, leading to problems with dampness and feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, and also can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked newspaper or soft rope. Remember to always load the tub with water prior to sealing, to permit the movement experienced when the bathtub is in use. The sealer can break rather early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently available on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or water resistant sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

We had been brought to that write-up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from an acquaintance on our other web blog. Do you know about someone else who is interested by the subject? Do not hesitate to promote it. Thanks so much for your time invested reading it.
Additional Information Report this page